Product Catalog - Order Toll Free: 1-800-382-8831


Product Index...

MOBILUP "The PREMIER FOUNDATION SYSTEM"

The ABESCO "MOBILUP" Permanent Foundation System is designed and engineered to support your RESIDENTIAL or COMMERCIAL modular building. The Mobilup Steel Stanchions bolted to concrete footings and to the steel "I" beam provides a strong, solid, and permanent foundation. The ABESCO system puts the Foundation where it should be, under the steel frame. With our foundation system, no perimeter bearing wall is required, saving you a substantial amount of time and money. Without having a perimeter bearing wall, it allows you to position your home with no special equipment making the installation simple and easy. State Approved Residential Plans State Approved Commercial Plans

Mobilup Mobilup

	Part #100

FOOTING EXTENDERS

When the property slopes more than 7" from side to side or end to end, footing extenders can be used to compensate for this and still allow concrete footings to be poured at grade level. Footing extenders come in varying sizes from 6" to 44" thus allowing the home to be set 5 feet off the ground.

Footing Extenders


Part #109 - 6"
Part #110 - 12"
Part #111 - 18"
Part #112 - 24"
Part #113 - 30"
Part #114 - 36"
Part #115 - 42"

RIDGE BEAM SUPPORTS

Adjustable Ridge Beam Supports provides for 6" of wood to earth clearance. The saddle will accept either 4" x 6" or 4" x 8" uprights and has 2" of height adjustment. Utilizing the same base plate as the Mobilup providing 2" of lateral adjustment.

Ridge Beam Supports Ridge Beam Supports

	Part #104			Part #105

CONCRETE ANCHOR TEMPLATE (With Anchor Bolts)

Concrete Anchor Template

Return to Top


INTRODUCING THE TUF-1

Our concept of using A.B.S. plastic pads, reinforced with 2" x 2" angle iron, drew a lot of attention at first. However, ABESCO has proven time and time again the durability of A.B.S. pads versus overweight concrete and pressure treated wood pads, through both engineering and practical testing and demonstrations. When put to a strain, plastic will bend, bow, flex, and twist, but will always return to its original shape. Neither concrete nor wood pads have these unique features. Once the concrete or wood fractures, forget about it, it’s finished and must be replaced.

The TUF-1 foundation system is also designed and engineered for both RESIDENTIAL or COMMERCIAL applications. The TUF-1 has 5 height ranges from 9 Ύ inches to 36 inches. State Approved Residential Plans State Approved Commercial Plans

TUF-1 TUF-1 Foundation Pad

	Part #501				Part #507

The simplicity of this system and the ease of installation allow us to offer this unique foundation system at a very substantial price reduction when compared to other systems on the market.

Return to Top


MEET THE EZ-TIE

The EZ-Tie is our "top of the line" tie-down system that uses the same ABS pads as our TUF-1 foundation system. The EZ-Tie also has 5 height ranges from 9 Ύ inches to 36 inches.

EZ-TIE EZ-TIE Pad

	Part #502				Part #506

As with the MOBILUP and TUF-1 foundation systems, our EZ-TIE system is State and County approved for both RESIDENTIAL or COMMERCIAL tie-down applications. Again, the ease and quickness of the EZ-TIE installation leaves ALL others in the dust. State Approved Plans

Return to Top


COMBINATION TIE-DOWN and PARTS

The ABESCO tie downs are engineered to meet the requirements from all states having tie down laws for both RESIDENTIAL or COMMERCIAL applications. ABESCO steel straps meet all U.S. Federal Government regulations and provide a secure attachment between the building and the earth anchor.

Below from left to right: 30" T.D.A. Double Helix (Part #601), Split Bolt w/Nut (Part #608), 7' Steel Frame (Part #613), Hole (Part #614) and Buckle (Part #606)Straps, Concrete (Dry) Anchor (Part #604), Expansion Bolt (included w/Part #604), Cross Drive Anchor Head (Part #607) and Stabilizer Plate (Part #616). State Approved Plans Pier--Pad--Tie-Down Installation Guide

30 Inch TDA Split Bolt and Nut 7 Foot Steel Straps Concrete Dry Anchor Expansion Bolt Cross Drive Anchor Stabilizer Plate

Return to Top


MISC. SET-UP PARTS

Below is pictured: Marriage Lock

Marriage Lock

		Part #704

Return to Top


STEEL PIERS

Our steel piers are state approved, quality engineered, and designed to meet and exceed all necessary requirements. All steel piers are listed and labeled for vertical loads (6000 pound rating) and are available 2" increments from 6" to 36".

Steel Pier


Part #306 - 6"
Part #308 - 8"
Part #310 - 10"
Part #312 - 12"
Part #314 - 14"
Part #316 - 16"
Part #318 - 18"
Part #320 - 20"
Part #322 - 22"
Part #324 - 24"
Part #326 - 26"
Part #328 - 28"
Part #330 - 30"
Part #332 - 32"
Part #334 - 34"
Part #336 - 36"	

Below is pictured: 16 Inch Pier Strap

Pier Strap

	Part #403

ASYMMETRICAL PIERS available in 2" increments from 6" to 36".

Asymmetrical Pier

Return to Top


STEEL PIER TOPS

Below from left to right: 5" Saddle Top (Part #400), 10" Saddle Top (Part #401), 5" Safety Top (Part #407) and Bolt-On-Top (Part #406).

5 Inch Saddle Top 10 Inch Saddle Top 5 Inch Safety Top Bolt-On-Top

***CUSTOM SIZES AVAILABLE UPON REQUEST***

Return to Top


ABS FOUNDATION PADS, PRESSURE TREATED WOOD and WOOD PRODUCTS

1" x 12" x 24" (Part #500) and 1" x 24" x 24" (Part #513) ABS pads

State Approved 12 x 24 Plans State Approved 24 x 24 Plans

1 x 2 ABS Pad 2 x 2 ABS Pad

1" x 8" x 16" (Part #511) and 2" x 8" x 16" (Part #510) blocking wood

1 x 8 x 16 Wood 2 x 8 x 16 Wood

Miner's wedge (Part #509) and pressure treated wood pads available in: 2" x 12" x 24" (Part #504p) and 2" x 12" x 30" (Part #505p).

Miner's Wedge Pressure Treated Wood Pad


ADDITIONAL WOOD PRODUCTS


Part #H-104: 2" x 6" x 12’ Doug Fir - Pressure Treated
Part #H-105: 2" x 4" x 12’ Doug Fir - Pressure Treated
Part #H-106: 2" x 4" x 12’ Doug Fir
Part #H-107: 2" x 8" x 12’ Doug Fir - Pressure Treated
Part #H-113: 4" x 6" x 36" Doug Fir
Part #H-114: 4" x 10" x 36" Doug Fir
Part #H-116: 2" x 4" x 20’ Doug Fir - Pressure Treated
Part #H-117: 2" x 4" x 20’ Doug Fir
Part #H-118: 2" x 4" x 14’ Doug Fir
Part #H-120: 2" x 10" x 12’ Doug Fir - Pressure Treated
Part #H-122: 2" x 12" x 12’ Doug Fir - Pressure Treated


CEMPLANK FIBER CEMENT PRODUCTS


Part #H-100: 4’ x 8’ Cempanel Vertical Siding
Part #H-101: 8 Ό" x 12’ Cemplank Lap Siding
Part #H-102: 5 ½" x 12’ Cemtrim Boards

Cempanel Vertical Siding Cemplank Lap Siding Cemtrim Boards

Return to Top


AWNING ACCESSORIES and TOOLS

Awning Anchor

Designed to be screwed into the ground and attached to the awning column post. 4" Helix, 11/16" dia. rod, 20" or 30" long. Available w/buckle head or 6" head w/slots for column shoe adjustment.

Awning Anchor


Part #800  - 30" W/Buckle Head
Part #800a - 30" W/6" Head
Part #810  - 20" W/Buckle Head
Part #810a - 20" W/6" Head

10" x 10" Freestanding Base Plate (Part #806) and 8" x 8" Safety Stake (Part #708)

10 x 10 Freestanding Base Plate 8 x 8 Safety Stake

6 Inch Auger Head Attachment (Part #611)

Auger Head Attachment

Gutter Stand and Auger Machine Rental and Sales

Gutter Stand Auger Machine

We manufacture awning post extenders. Stock post extenders are powder coated white. In stock we have 1, 2 & 3 foot extenders in 45 and 90 degree angles. Custom sizes and colors are also available. Part # 808.


OTHER PRODUCTS and SERVICES AVAILABLE

ABESCO is a distributor of Duralum aluminum products. Please call us for a free price quote. We sell do-it-yourself kits to the public and we also have an expert installation team that is second to none in the industry.

Awning Picture Awning Picture

Awning Picture Awning Picture

Return to Top


MISC. PARTS and SUPPLIES

Nuts and Bolts


CUSTOM METAL FABRICATION


METAL SUPPLIES


CONCRETE WORK

Return to Top


PRODUCT TESTING

Random testing is conducted at different times of the year by an independent engineer to insure strength and quality.

Testing

The ABS pad is designed to flex but not break.

Testing

32,000 pounds! Almost 3 times the engineered load requirement.


A TRUE WORKING SHOP

ABESCO prides itself on being one of the few true working shops around. We cut, punch, weld and press 90% of the products sold. Our certified welders and machinists are some of the best available. And all of our machines in the production of our products are repaired by shop employees. Safety is always number 1 and pride is a close second.

AIDA Punch Press

Machine

Work In Progress

Machine

WYSONG Power Squaring Shear

Machine


"GOLIATH"

Niagara

Built in 1942 by Niagara Machine and Tool Works in Buffalo N.Y. This press is the backbone of the shop exerting 190 tons of pressure. It is a true monster.

Return to Top